Repair of a soft roof mkd. Overhaul of the roof of an apartment building

roof roof repair apartment building sooner or later concerns every tenant who lives in a building of this type. Roof problems are especially acute for those whose apartments are located on the upper floors. The driving factor for repairs is most often a leaking or blowing roof. The reason may be low-quality roofing materials or roof wear associated with the age of the structure itself. In the second case, the overhaul of the roof of an apartment building is especially acute.

Often, residents of a house whose roof is in need of repair turn to various authorities that are engaged in house maintenance. But in rare cases, their appeal leads to a result. More often, residents have to raise money for roof repairs on their own.

But before complaining management company or hire builders and pay for roof repairs, you should figure out what type it belongs to and identify the cause of leaks.

What are the roofs of apartment buildings

Repair of different roofs can vary significantly, so it is important to know which type it belongs to. According to the design of the roof are:

with one slope;
with two slopes;
multi-slope;
flat;
complex.

The roof structure consists of an outer covering, a support, a drainage system, insulation and waterproofing. The support is a reinforced concrete slab or rafter system.

Important! Drainage systems are installed only on flat roofs, pitched structures do not need them, since the water itself flows down from an inclined surface.

Flat roof repair options

Repairs of the roof of multi-storey buildings are divided into partial or current and capital. Current repairs are carried out if the coating wears out or any defects appear in it. Most often, roofers are limited to replacing the old roofing material on a new one and sealing all cracks. New canvases can be laid in one or two layers. At the end of the work, all seams and joints are sealed with sealant.

Maintenance of the roof of an apartment building is not very expensive, so it is the most common. But there is another repair option, in which new layers of canvas are not required to be laid. Cuts are made on the canvas in the places of the defect, the edges are bent and the internal space is cleaned. Then this place is dried gas burner and covered with a layer of mastic. She coats the base of the roof and roofing material. The edges are put in their original place and pressed tightly until they are fixed.

If there are rotten areas, they are cut off and cleaned. Places with a defect are poured with bitumen, and then a piece of a new canvas is glued to the old roofing material. Of course, this option is not entirely high-quality, but because of its cheapness, it is most common, especially during repair work on the roofs of old buildings.

During major repairs, the old roof is completely replaced with a new one. All old material is removed and cleaned, fresh screed mixture is poured, and two layers of new coating are laid. Such repairs should be carried out only by specialists, since if the process is violated, the ceiling of the upper floor can be damaged.

The basis of the technology for the overhaul of the flat roof of an apartment building is the fusing of roofing material with a special gas burner. The roofing material is heated from below, after which it is gently pressed against the base of the roof. It is important to maintain a uniform temperature here, since too high values \u200b\u200bof it can destroy the roofing material. The coating is laid with an overlap, and all seams are treated with a building sealant.

Causes of roof leaks

Roof leaks can only be stopped with major repairs. The reasons for the appearance of a leak can be different, often they make themselves felt during the period of melting snow or heavy rains. The main causes of roof leakage in an apartment building are as follows:

the expired service life of the roofing material, since over time the roofing material is destroyed, its service life is up to 15 years;
violation of the integrity of the roofing material due to careless work when removing snow from the roof;
use of poor quality materials;
violation of the technology of laying roofing material;
difficulties in installing plants that can damage the roof with roots;
violation of the attic temperature regime; according to building codes, the temperature in the attic should correspond to the conditions outside.

Important! Insulating the attic can lead to leaks in the roof.

Before demanding repairs to the roof of an apartment building, you should understand the cause of such a defect. The source of damage is usually found at the site of the leak. On roofs covered with soft bitumen, it is very easy to find a problem area - the roofing material rises on it due to trapped air. In this case, the ruberoid carpet is completely rebuilt and the leak is dried. To perform such work, specialists are needed; it is not worth re-laying the roof on your own.

The existing regulations say that scheduled repairs with the replacement of damaged parts of the roof should be done twice a year, but in reality this is rarely done. This defect detection technique is suitable for apartment buildings with a flat roof.

What are the leaks

The nature of the leak also plays a significant role in the process of establishing the correct cause of a roof leak. According to the technical regulations, leaks can be:

storm - occur during heavy rains and often occur due to poor-quality work of the drain;
snow - appear when the lower snow layer in contact with the roof thaws;
dry - appear as wetting of the ceiling and walls, possibly due to accumulations of condensate;
flickering - occur at any time of the year, regardless of the weather, the cause is usually cracks in the waterproofing or improper roofing technology.

It is easier to fix snow or storm leaks, as it is easier to recognize the causes of their appearance. Things are more complicated with flickering and dry options, since it is difficult to find the source of the problem, which is often localized in one area.

Pitched roof repair technology

Pitched roofs are usually covered with painted or zinc coated metal sheets. In this case, partial repair of the roof of an apartment building consists in finding damaged areas of the coating and replacing them, as well as control over the base of the roof under the roof. It happens that the inner crate or rafters are rotten and require restoration. To do this, the sheets of the outer coating are removed. Sometimes it is necessary to replace the layers of waterproofing or insulation.

If the problem areas are small, then patches are placed on them and the seams are treated with sealant. Even small gaps must be sealed, otherwise they may become a source of leakage in the future. Damaged areas are degreased and treated with a primer before repair. After the repair is completed, the roof is painted with a special paint, which should increase the strength and extend the life of the roofing.

The technology for the overhaul of the roof of an apartment building with a pitched roof is similar to the technology for the current one, but with a larger-scale replacement of all materials.

Important! Please note that the cost of major repairs is much more significant than the current one.

Who pays for roof repairs?

When the need for repairs arises, the question arises, who should pay for the repair of the roof in an apartment building? Capital and current repairs must be carried out by the management company or a contractor hired by it. The roof is a common house property, so the cost of maintaining it falls not only on the residents of the upper floors, but also on everyone else living in the house.

If a leak is found and they want to fix it, then first of all it is necessary to write an application for repairing the roof in an apartment building, which indicates the location and cause of the defect. The document is drawn up in two copies, and transferred to the managing organization.

If the leak caused material damage, a specialist from the management company should be called in to assess the losses and draw up an act.

Within ten working days from the date of the application, the company must send a specialist to inspect the roof. Based on the shortcomings seen, he draws up a defective statement. It serves to draw up an estimate and determine the financial and labor costs that will be needed to fix the leak.

Important! It should be noted that only at the general meeting should the issue be decided - at the expense of the residents of the house or not, repairs will be made. More than 50% of residents must make a decision “for”. This conclusion is officially fixed by the protocol.

To date, most residents of multi-storey buildings are faced with many problems in the repair and maintenance of the house. And many of these residents do not even know how to act in a particular case in order to solve certain problems.

Quite a lot of problems arise precisely when it is necessary to repair the structures of the house. Our article is designed to overhaul the roof of a house in which there are many apartments without spending a lot on it. Money and without breaking the law.

First of all, it is worth deciding what exactly is meant by such work as repairing the roof of an apartment building. In this case, this is the implementation of the repair of the uppermost part of the building, which further protects the entire house from the negative effects of weather conditions.

drainage system, moreover, it should be for any design and shape of the roof.

The drainage system is equipped in the form of an internal or external drain. Modern options the roofs of apartment buildings are also hydro- and thermally insulated. If some problem arose and the roof had to be overhauled, then it is worth considering several elements.

Only the use of high-quality and high-tech building materials will make it possible to repair the roof of a multi-storey building effectively, and this will increase the operational and technical parameters of the roof in the future.

Features of repairing the roof of a multi-storey building

In the construction of today, as a rule, the repair of the roof of an apartment building is divided into capital and partial. If we talk first about the partial repair of the roof, then it is necessary when minor defects appear, leading to a decrease in the performance of the roof. During partial repairs, as a rule, defects such as:

leaks on the roof or on the roofing;
noise that is almost completely eliminated;
restore specific elements of the roofing;
give the roof of the house an attractive look.

If some leaks have begun to appear on an apartment building, then it is first worth inspecting the roofing to identify places where the roof is leaking. Already starting from which elements of the roof have been damaged, you can begin to replace the structural elements of the roofing, for example, they often replace, renew the layers of waterproofing, change the crate and other elements of the coating under the roof.

When all the repair of the damaged sections of the roof has been completed, it is worth starting work on sealing the joints that have appeared in the areas that were being repaired, as well as sealing the seams on the roof covering.

It is worth knowing that different types of roofing require the use of different types sealant, for example, it can be mastics, silicone and other sealants.

To find out what kind of repair is needed on the roof of an apartment building, we tried to process a large amount of different information and came to the following conclusion: a major overhaul of the roof on an apartment building is necessary only if the roof was damaged really very seriously.

Most often, a major roof overhaul involves the replacement of all elements that hold the roof structure, among which are rafter system, drainage system, storm drain system and crate.

It happens that the residents of the house have a question: does it perform on this moment the roof of our house has all its technological functions and is it worth doing a major overhaul of the roof or does it need to be completely changed?

Programs for the overhaul of the roofs of multi-storey buildings

Of course, everyone is well aware that the repair of roofing will require a large amount of money. It is in connection with this that many residents of high-rise buildings are interested in who should carry out this repair?

We draw your attention to the fact that in many cities in Russia there are currently such programs, according to which major repairs of the roofs of multi-storey buildings are carried out at the expense of the Housing and Communal Services Fund.

This program provides financial support to managing organizations and associations of owners of apartments in multi-storey buildings. In addition, such financial assistance can even amount to as much as 95% of the total cost of a roof overhaul.
Worth knowing: for your house to be included in such a program, the owners of all apartments must make one decision that would indicate that the house, or in this case the roof, really needs a major overhaul.

You also need to draw up and approve a document for roof repairs, which will allow for a major overhaul, and will also say that all residents of the house have made a mutual decision to participate in such a program.

After that, the manager of the residents' organization must apply for their home to participate in the program, which is assigned to the local government.

The overhaul program is valid only for specific types of work. The list includes not only major repairs, but also partial replacements of individual roof elements, for example, truss systems, trusses, roofing.

Repair work includes:

fire-fighting treatment of the roof and antiseptic treatment of wooden structures;
roofing replacement;
restoration of temperature and humidity conditions in the attic;
replacement of external and internal drainage.

We completely change the truss system of the roof of the house

It is worth considering that multi-storey buildings, in which the degree of wear is already 70%, are not subject to major repairs. Such buildings are classified as emergency, so they need to be reconstructed or completely demolished.

As a rule, the city budget is able to allocate only 95% of the cost of a roof overhaul, so 5% of the cost for the overhaul will have to be paid by the tenants of the apartment building themselves, housing cooperatives or a homeowners association.

To receive such financial assistance under the state program, it is worth presenting a package of the following documents:

an application for financial assistance;
documents from legal entity for the management of a multi-storey building;
certificate of registration in government bodies this legal entity;
extract of details from the bank from the applicant's account;
minutes of the meeting of apartment owners in a multi-storey building on the choice of a management company and a list of various repairs;
a copy of the agreement on the management of a multi-storey building;
a project and a document that allows for a major overhaul of the roof of the house;
the minutes of the meeting of all the apartment owners of this house, which says that it was mutually decided to carry out a major overhaul of the roof, the cost of the work was determined, the procedure for performing repairs was considered, and the apartment owners contributed 5% of the roof repair cost.

All this must be documented.

The decision is legal only if 2/3 of all apartment owners voted for it;
register of apartment owners;
an agreement with organizations for the repair of the roof of an apartment building.

It must be remembered that copies of documents must be certified by the head of the organization.

Correctly fill out an application for roof repair

All the documents that we have listed above should be presented to the city's housing and communal services committee. The decision on whether the state provides financial assistance to a particular house for major repairs will be made within 10 working days.
State assistance is issued to residents of a multi-storey building for repairs, in accordance with the Federal Law of the Russian Federation of July 21, 2007. No. 185-FZ “On the Housing and Utilities Reform Assistance Fund”, as well as Federal Law No. 323-FZ of December 30, 2008.

How to create a contract for a request to help in the overhaul of the roof, you can find out in any housing department. But, if the house does not meet the criteria specified in Article 14, the apartment owners will not receive financial assistance. By the way, one of the criteria of the law is the absence of debts for all owners of apartments in the house.

How to write an application to the housing department

If other defects were found, which can be corrected only through prompt repairs, then the owners of all apartments in this building should urgently contact the housing department for help.

In this case, no one will want to listen to just an oral appeal, so it is better to make a written request for roof repairs. Only if the application is written, will it be considered by the department.

How to fill out the application correctly:

The header of the application must contain the name, patronymic and surname of the manager of the housing department, as well as the data of the person who fills out the application: his full name and address of residence.
In the text of the application itself, it is worth indicating the state of affairs, that is, when exactly and where exactly the leak occurred on the roof of the house. Try to describe in as much detail as possible where the water came from, as well as what material damage was caused to the apartment.
The final part of the application contains a similar request: "I ask you to repair the roof of the house above my apartment."
At the end, you need to put the date of circulation and signature.

Worth knowing: the application must be written in 2 copies, since one must be written for yourself, and the second must be taken to the housing department. In this case, the application must be reserved, and your copy must contain the number and date when the application was accepted, as well as the signature of the person who confirmed your application in the housing department.

The roof of the house should be repaired by a contractor

As soon as your appeal is received by the housing department, employees should immediately contact a contracting company that specializes in such repairs. The specialist of the organization will assess the scope of the necessary work and draw up a list of defects that need to be repaired.

If your house cannot receive financial assistance from the state for certain reasons, then the cost of repair work will need to be divided equally among the owners of apartments in the house.

Tip: the total amount should be divided in proportion to the area of the apartment between all owners. It happens that a mistake is made, and the amount is divided by the number of residents in each apartment, but this is wrong.

Only after the amount indicated by the specialist has been fully paid, the repair will begin and everything will be completed as soon as possible.

There are housing departments that take advantage of the fact that the legislation prescribes the time frame for repairs to be carried out, but you have every right to motivate that paragraph B in Article 40 says that the housing department employees must correct and repair the entire problem as soon as possible situation if it is considered an emergency.
Know that everything depends on your own activity and perseverance. If you insist, then the housing department workers will begin to take measures to quickly eliminate defects or repair the roof of your apartment building.

When you were able to achieve at least some positive results from the housing department, you should not stop there. Ask which contracting company will do the repair and demand that you draw up a contract with it.

If you are refused to provide information, then you can safely contact a lawyer. There are many methods that will help the manager of the organization to bring the case to the end without trial. You just need to do everything correctly, following all the recommendations that have already been mentioned.

Only in this case it is possible to achieve roof repair with a minimum of costs, without spoiling your health in this way.

Flat roofs are often used in the construction of modern high-rise buildings, administrative and industrial buildings, and in suburban construction. In the latter case, they are most popular when creating low-rise buildings or outbuildings.

Basic requirements for flat roofs

The increased strength of the roof is very important for regions with heavy snowfalls. During winter periods, it will have to withstand a significant load as a result of the formation of a thick layer of ice and snow. This indicator is very important in the case of creating an exploitable roof.

A flat roof should function reliable protection from rain and melt water and have a sufficient slope so that precipitation does not linger on it.

The design should not deteriorate under the influence of severe frosts and the scorching rays of the sun, sudden temperature changes and heavy hail.

It should perfectly cope with the heat-insulating function.

All materials used in the construction of the roof must be fire resistant.

Pros and cons of flat roofs

Pros:

Flat structures have a much smaller area than pitched ones, which makes it possible to save significantly on materials and during construction and installation work.
The smaller footprint helps to optimize costs.
It is possible to cope with the construction of such roofs in a shorter time than with the installation of pitched ones, since all the required materials can be located in close proximity - literally at your feet.
Due to the same feature, maintenance and repair work is simplified: their implementation on a flat horizontal surface is greatly simplified.
On flat roofs, it is convenient to carry out installation and necessary service work that requires the use of special equipment: solar panels, air conditioning systems, antennas, etc.
When creating a flat structure, you can get additional meters usable area and use them as a recreation area, sports ground or arrange a flower garden, garden. Currently, it is possible to cover the roof with paving stones or paving slabs through the use of special technologies. A roof paved with high-quality tiles, combined with garden furniture, a green area, a gazebo, will be an ideal place for a family holiday.

Minuses:

with heavy snowfalls, snow mass will accumulate on the surface, which, with the onset of melting, often leads to the formation of leaks;
often there is a need for the use of drains;
in the cold season there is a risk of freezing of the internal drain;
the drainage system is often clogged;
a mandatory requirement is the mechanical cleaning of the surface from the snow mass;
need periodic monitoring of the state of the insulation to prevent its moisture;
From time to time it is necessary to check the safety of the tightness of the coating.

Types of flat roofs

There are four main types flat structures:

Exploited roofs

Their peculiarity is the need to create a rigid base - otherwise it will not be possible to maintain the integrity of the waterproofing layer. The base is a screed based on concrete or corrugated board, which is necessary to create a certain slope for water flow. The heat-insulating material used in the installation of the operated roof will be subjected to significant static and dynamic loads and must have a sufficient level of compressive strength. With a small stiffness of the insulation on top, a cement screed device will be required.

Unexploited roofs

When arranging this variety, there is no need to create a rigid base in order to lay the material for waterproofing. You don't need a hard core either. For further maintenance of the roof, bridges or ladders are arranged, the function of which is to uniform distribution loads on the roof surface. The construction of unused flat roofs will cost much less, but they will not last as long as exploited ones.

traditional roofs

The structure of traditional types of roofs provides for the location of a layer of waterproofing material over heat-insulating. The basis for the roof is a reinforced concrete slab, and water is drained from the roof surface by creating an inclined screed of expanded clay concrete.

Inverted roofs

Roofs of the inversion type practically solved the problem of leaks - the main drawback of flat structures. In them, the thermal insulation is located above the waterproofing carpet, and not under it. This technique helps protect the layer of waterproofing material from the damaging effects of solar ultraviolet radiation, sharp temperature fluctuations, the freezing process and subsequent thawing.

Compared to other types of roofs, inversion is more durable.

In addition, it is distinguished by increased functionality: you can arrange a lawn on it, make tiled masonry. The optimal angle of inclination of such roofs is considered to be from 3 to 5 degrees.

Device Features

The main subtleties of the construction of flat roofs are as follows:

Vapor barrier is arranged by means of a bitumen-polymer membrane reinforced with fiberglass. Another option is to lay a vapor barrier film over the screed.
Along the edges of the roof, a layer of vapor barrier material is wound vertically so that its height is greater than the height of the insulation layer, after which the seams are sealed.
Above the vapor barrier, insulation is laid (in the case of a traditional roof).
A protective carpet is laid over the insulation, which is made of waterproofing materials with a bituminous base.
If expanded clay is used as a heater, a cement screed must be made under it. Waterproofing is laid in two layers on it.
When installing light structures for which significant loads are not provided, it is necessary to glue the waterproofing sheet along the entire roofing perimeter.

Mounting

A flat roof cannot be laid strictly horizontally - a minimum slope of at least 5 degrees must be observed. This requirement is due to the need to ensure the descent of rainwater and snow from the roofing surface. Another important point: it is necessary that the slope be created not only by the coating, but mainly due to the correct implementation of expanded clay or slag bedding. Even if the slope angle reaches 10 degrees, this will not interfere with the uniform laying of the heat-insulating material.

Lightweight flat roofs

In the construction of such roofs, the work is divided into several stages.

As a result of the work done, a warm and fairly reliable flat-type roof is obtained: in the context, it resembles a multilayer cake based on several components.

Hard roof device

When creating floors of this variety, expanded clay is best suited as a heat-insulating material. Minimum Thickness its layer should be 10 cm. Above the laid expanded clay, it is necessary to perform cement-sand screed thickness from 40 to 50 mm. To ensure greater strength, a reinforcing mesh is placed in its middle layer. Such a measure is necessary to maintain the integrity of the coating while people are on it during repairs, maintenance, etc. In addition, it is these roofs that are optimally suited as the basis for a pool or recreation area.

The manufacture of beams of such structures is most often carried out on the basis of a metal channel, since parts made of wood will not withstand significant loads.

Another requirement for the installation of operated roofs is the sufficient thickness and strength of the walls of the house.

Methods for arranging flat structures

There are several basic ways to create flat roofs:

Through the installation of concrete floor slabs. Such work can be done in a fairly short time, but special lifting equipment is required. The use of this method involves the implementation of insulation. The material can be laid both inside and outside.
Using metal channels or I-beams, on top of which it is necessary to lay boards: their thickness should be 25-40 mm. A layer of expanded clay is poured on top, then a concrete screed is created.
The creation of the overlap is carried out by means of monolithic concreting. This requires a high-strength formwork with thick supports. The supports are fastened together with jumpers. This type of overlap also needs to be insulated.
With ceramic blocks large sizes: they are laid on top of metal beams. Such blocks replace wooden flooring. The main advantage of this method is the use of ceramics, which are characterized by increased mechanical strength, resistance to moisture and excellent sound and heat insulating properties. Large-sized ceramic blocks do not need additional insulation: when using them, you can limit yourself to such a measure as creating a concrete screed.

CONCLUSIONS:

Flat roofs are often used in the construction of modern high-rise buildings, administrative and industrial buildings, and in suburban construction.
Flat structures must have increased strength - especially when a large amount of precipitation falls.
Flat roofs have a much smaller area than pitched ones, which allows significant savings on materials and during construction and installation work.
The main disadvantage of such roofs is that during heavy snowfalls, snow mass accumulates on the surface, often leading to the formation of leaks.
Flat roofs can be exploited, non-exploited, traditional and inversion.
Roofs of the inversion type practically solved the problem of leaks - the main drawback of flat structures.
A flat roof cannot be arranged strictly horizontally - a minimum slope of at least 5 degrees must be observed for atmospheric precipitation to drain.
Lightweight flat roofing is fundamentally different from hard roofing.
Flat roofs can be created in several ways.

In the video you can see how to drain a flat roof using a non-combustible Rockwool insulation system.

The problem of leakage and poor condition of the roofs of apartment buildings has been quite acute for several decades. These are not only leaks, but also collapses in old houses, poor quality of the coating, gradual destruction of the rest of the house structure. Therefore, an apartment building is one of the most important problems of its general maintenance.

Repair of the roof of multi-apartment buildings should be serviced by the management company of this building.

Residents of any apartment building pay utility bills, part of which goes to maintaining the house and its roof in proper conditions. Such repairs should be carried out by employees of the organization accepting payments, although it is quite common to encounter their inaction. Residents, as a rule, collect funds themselves and turn to specialists who carry out such work.

But before contacting the housing office or ordering contract work, you need to clearly understand their volume, the causes of leaks. In our article, we will consider what the roof of an apartment building is, what problems can arise during its operation, and how they are solved.

Types of roofing of an apartment building

To begin with, let's decide what types of roofs are in apartment buildings, since repair work here can vary greatly. By design features and the shape of the roof, they are divided into:

slopeless (familiar to all flat roofs, which are the majority);
single-pitched (with a different angle of inclination);
gable;
multi-slope;
(now they are quite rare among houses of old construction, most often these are new buildings).

The roof itself is the following structure: it is an external covering and an internal support (rafter system or reinforced concrete slab). A storm drain system is required, which can have an internal or external modification, all modern roofs have a waterproofing and insulating layer. Anyone should be organized taking into account all the features of the design.

Roof repair options

Causes of roof leaks in an apartment building

Only a major overhaul of the roof can help with such an unpleasant phenomenon as leaks. The reasons can be very different, but usually such leaks appear only during heavy rains and during the thaw period, when large masses of snow begin to actively melt. There may be several reasons for leaks, therefore, when ordering repairs, it is necessary to correctly identify them, since the type of repair work, cost, and the use of certain materials and technologies will depend on this.

Consider the reasons that can cause leaks in the roof of an apartment building:

Violation of the integrity of the carpet as a result of work on cleaning ice and snow. Often this is caused by incorrect actions, inattention and negligence of those who carried out such work.
Material expired. Ruberoid and other roofing materials have their own shelf life, after which the risk of damage to such material increases. Many recommend carrying out preventive work or, after a certain time, completely replacing the roof covering and making a major overhaul.
Violation of technology when laying roofing material can also cause many troubles in the future, including leaks;
Use of poor quality material. When laying a roofing carpet, many seek to save money, but this only leads to an increase in costs in the future, because such material will not be able to maintain all the required properties for a long time.
Often leaks occur when. Plant roots can damage the waterproofing material, causing leaks.

One of the causes of leaks that can cause major roof repairs can be temperature disturbances in the attic space. According to the regulations, in the under-roof space, the temperature in the winter months should be equal to the outside temperature, that is, it is impossible to insulate such attic spaces, as is often done now.

Search for leaks

But before ordering a major roof repair for leaks, it is necessary to correctly determine the location of the damage. Usually for this it is enough to climb the roof, comparing the place of the leak, find it on the roofing. When using soft, bituminous roofs, it is very easy to find such a place - it is given out by air bubbles.

In this case, it is recommended not only to replace a piece of material, but also to completely remove the entire carpet, dry the damaged area thoroughly, since moisture, most likely, has already managed to soak everything. Only specialists should perform such work, it is almost impossible to do it independently and qualitatively and reliably.

We have considered the main options for planned and capital works. But, unfortunately, it is problematic to carry them out on your own. Therefore, we do not give an example of a system of calculations and costs. Each case is completely individual.

What to do, how to solve a similar problem? You will have to go to the management company more than once or organize roof repairs at the expense of own funds residents of the house.